Group

Frequently Asked Questions

Tag : Routing

The shank length is 63mm, the overall length is 115mm.

... Read more

No, the 1/4 collet is actually 6.35mm, a difference of .35mm which is critical in terms of collet and shank sizes.

... Read more

The part numbers are: CE/127127 & CE/127635.

... Read more

The overall length of a 5/53X1/2TC is 103mm.

... Read more

The dimensions of the router plate is 306mm x 229mm x 6.35mm.

... Read more

The cutter required is 3/83X1/2TC, 3/83DX1/2TC, 3/85X1/2TC, RT/11X1/2TC.

... Read more

A sleeve will fit on to the shank of the cutter to increase the shank size, where as a collet will fit into the router to enable different shank sizes to be inserted in to the router.

... Read more

Total cutting height is 35mm.

... Read more

A B63B will fit both cutters.

... Read more

B35C is the bearing required.

... Read more

It is a cutter for cutting circular hinges. Trend offer the 104, 105 & 421 groups for this purpose.

... Read more

To convert the PDS set into a tongue and groove cutter set the following are required SP-34/74TC, SPACER/8

... Read more

You can not re-sharpen the 10/99 because the dimensions for the tongue and groove will change making them incompatible, however, the pocket whetstones if used will help to keep a keen edge on the carbide.

... Read more

A rule joint can be cut with either the OCTACUT sets or something like the 7/5X1/4TC and 6/5X1/4TC cutters.

... Read more

We now offer a 60 degrees V-groove with a 1/4 shank (ref 11/20X1/4TC) and also a larger diameter 45 degrees V-groove which has a 19.1mm diameter by 1/2 shank (ref 11/41X1/2TC).

... Read more

The T10/T11 trammel bar and attachment can be used on any router that uses a 10mm diameter fence rod.

... Read more

The cutter required is trend ref 36/19X1/4TC.

... Read more

The cutter that will give a fine finish on both veneers is either the 14/1x1/2TC or 14/2x1/2TC, up and down shears.

... Read more

The holes are 6mm and 24mm between centre.

... Read more

The T5 beam trammel or attachment can be used on any router that uses an 8mm diameter fence rod.

... Read more

The UNIBASE is required.

... Read more

The templates can be clamped or stuck with double sided tape.

... Read more

The UNIBASE is required.

... Read more

The thickness of the Trend Unibase is 8mm.

... Read more

In the UK and America, jigs work in imperial sizes the cutter set required is SET/MT1X1/4TC, SET/MT1X8MMTC. For jigs set up in millimetres the cutter set required is SET/MT2X8MMTC.

... Read more

The overall length of a 3/83X1/2TC is 108mm

... Read more

The overall length is 109mm.

... Read more

34/15TC.

... Read more

The overall length of a 3/82X1/2TC is 79mm.

... Read more

The shank length is 57mm the overall length is 108mm.

... Read more

The overall length is 99mm.

... Read more

Slotseal Carripile is not available from Trend. Carriplie II was made originally made by Slotseal. Reddiseals offer a similar centre leg pile carrier.

... Read more

The overall length of a 3/83MX1/2TC is 84mm.

... Read more

Schlegel Engineering, Henlow Ind Estate, Henlow Camp, Bedfordshire, SG16 6DS Tel no. 01462 811963.

... Read more